Packet tracer labs company serial#

200-301 V2 Ch16: Controller-Based NetworksД¬hapter 6 of the CCNA 200-301 Official Cert Guide, Volume 2 discusses Cisco switch port security, from concepts, configuration, to verification.

200-301 V2 Part 4: Network Architectures.

200-301 V2 Ch12: Miscellaneous IP Services.

200-301 V2 Ch05: Securing Network Devices.

200-301 V2 Ch04: Security Architectures.

200-301 V1 Ch25: Configure IPv6 Routing.

200-301 V1 Ch24: Configure IPv6 Addressing.

200-301 V1 Ch18: Troubleshooting Routing.

200-301 V1 Ch16: Router Addresses and Routes.

200-301 V1 Ch14: Analyzing IPv4 Subnets.

200-301 V1 Ch12: Classful IPv4 Networks.

device, ping the Other Company server at 172.16.10.2.Д®nd of document Scripts ACME1 Configuration end device and navigate to the Other Company server by entering its IP address of 172.16.10.2

Similarly, OtherCo1 should now know about the route to the ACME network 192.168.0.0/24. ACME1 should have learned the route to the Other Company network 172.16.10.0/24.

Look at the routing tables on ACME1 and OtherCo1.

Use the show ip bgp summary command to verify the routes that ACME1 has learned via eBGP and their status.

The show ip bgp summary command is very useful here.

Verify that ACME1 has formed an eBGP adjacency with ISP-Entry-1.

OtherCo1(config- router)# neighbor 1.1.1.9 remote-as 65003 Use the 1.1.1.9 as the neighbor IP address of ISP-Entry-2 and add the Other Company internal network 172.16.10.0/24 to BGP. Other Company is under AS 65002 while ISP is under AS 65003. Because of this, you must also configure the Other Company end of the connection.Д¬onfigure router OtherCo1 to form an eBGP adjacency with ISP-Entry-2, which is the ISP border router facing OtherCo1. The network administrator at Other Company is not familiar with BGP and could not configure the Other Company side of the link. Part 2: Configure eBGP for Other Company Inc. Use 1.1.1.1 as the neighbor IP address and add the ACME internal network 192.168.0.0/24 to BGP.ДЄCME1(config- router)# neighbor 1.1.1.1 remote-as 65003ДЄCME1(config- router)# network 192.168.0.0 mask 255.255.255.0ДЇrom any device inside of the ACME network, ping the Other Company internal server again. ACME has AS number is 65001, and the ISP is using AS number 65003.

Configure ACME1 to become an eBGP peer with ISP-Entry-1.

The pings should fail because no BGP routing is configured at this time.

From any device inside of the ACME network, ping the Other Company server at 172.16.10.2.

Packet tracer labs company serial#

From ISP-Entry-1, verify that the ISP has provided IP reachability through its network by pinging 1.1.1.9, which is the IP address of the ISP-Entry-2 Serial 0/0/0 interface.

ISP-Entry-1 is the ISP border router that is directly connected to ACME. Because the ISP is using BGP as the routing protocol, you must configure ACME1, which is the ACME border router, to establish a BGP neighbor connection with ISP-Entry-1.

You must connect ACME to the ISP so that ACME and Other Company can communicate.

The ISP has established network reachability within its network and to Other Company. hired an ISP to provide a connection to a partner company called Other Company.

Instructions Part 1: Configure eBGP in ACME Inc.ДЄCME Inc.